Updated at: 06-09-2022 - By: Sienna Lewis

The simplest method to give your living room some individuality and style is to change the curtains. However, prairie curtains are typically disregarded when it comes to designing.

There aren’t many stores that carry this sort of curtain. To preserve their culture, families and communities have passed it down from generation to generation over the years. Prairie curtains can be made using the instructions in this page.

Fortunately, if you have a few simple things on hand, they aren’t difficult at all: Both homespun and muslin fabrics have both front and back sides, making them easier to sew, but muslin has a more classic look, so be sure to buy enough yardage depending on how wide and tall your curtains will be.

Steps on Making Prairie Curtains

Measurement is the first stage in the process of making prairie curtains. A yardstick or meter stick can be used to measure the window’s length. Add 5 inches to this number, and then measure the breadth of your cloth with one of these instruments to get the correct size.

You’ll need two pieces of homespun – one for the top panel and one for the bottom panel – to drape over your windows while they’re open on the rods.

Drawing a diagonal line across the fabric from one corner to the other will create two similar triangles on the fabric. Work on a flat surface, aligning both fabrics so that their widths run in straight lines from one end to the other.

How to Make Prairie Curtains? 9 Simple and Easy Steps! - Krostrade

As soon as this is complete, draw a diagonal cutting line across the middle of each rectangle as shown above, and then cut along it either vertically or horizontally! Use vertical stitches when doing this, and only cut up (a minimum of 2 inches per stitch).

Step #3: Lift and leave the homespun fabric on the right triangle.

You can return to where you started by spinning this strip of fabric in a horizontal line until you reach the bottom side, but this time, flip it over so the bottom side is now facing up.

Using only two triangles of cloth as your starting point, you may quickly and easily design a whole new pattern.

Observing the two mirror-image triangles, you may note that right angles are set around the outside edge of each curtain, and shorter points are set on both ends of each curtain.

Using a pair of scissors or a knife, take 7 inches from the inside edge and place it at the intersection of these lines, so that they are sliced into equal parts.

pinning the homespun fabric to the muslin is step five in the process of making prairie curtains.

After that, sew all but one of the sides, leaving a hole so you may turn it right-side-out and press the edges before hanging it up!

Curtains need to have the top border of each curtain folded back an inch while sewing them. With a needle and thread or pins if you don’t have needles on hand, fold it down 3 inches and pin it in place.

To create rod pockets for hanging reasons, make sure that when you extend out both sides, they’re mirror images of one another from left to right across the breadth!

Make two marks at 10 and 11 inches from the top of the outside edge of the cloth, and you’re ready to begin sewing a rod pocket.

The next step is to follow the slope side inside edge, measuring up from the bottom hem of the curtain, starting with the measurement for each line.

Connect these points with straight lines, and you should have two channels 5 inches apart, each traveling in the opposite direction (one channel has one vertical point).

This is the eighth and last step.

  1. Make sure the cloth is 4 inches longer than the finished length of the curtains before you begin.
  2. Measure the width of two pieces of cording, and slit one inch from the outer border of each of the two cords on one side only (this will later allow you to thread the cord through).
  3. Before trimming the extra, sew the two strands together with a needle and thread.
  4. Sew over these points securely near where they enter the muslin layer by stitching along just inside edges on opposite sides so that they do not go beyond or cause holes within layers themselves by threading each length of cord into its respective curtain panel until it reaches either end.

The final phase in the process of making prairie curtains is the installation. Hang your curtains with the home-spun cloth facing the room. A large knot will keep it from slipping through the cut gap in the curtain rod’s metal frame.

THINGS YOU WILL NEED

  • the aforementioned measuring device: the tape
  • Distressed textiles
  • Muslin
  • Pencil
  • Scissors
  • Pins
  • There is a sewing machine in the room
  • Iron
  • a cotton twill cord

TIP

To make the cord openings look neater, add a small hem by hand stitching them closed.

  1. The window’s length should be known. To figure out how long your cloth should be, multiply the length by 5. To determine the proper width of your cloth, take a measurement of the window’s width. Cut one piece of muslin and one piece of homespun cloth to this size.
  2. Spread the homespun over the muslin and line the edges of your fabric on a flat surface. Orient the cloth such that the fabric’s width is horizontally aligned with its length. Draw a diagonal line from the top right corner to the bottom left corner of the fabric.. Make two similar triangles from each cloth by cutting along the line.
  3. Dispose of the hand-spun cloth in the right triangle by lifting the corners up. The triangle on the left should remain untouched. It’s time to switch sides of the right triangle’s muslin fabric. In order to duplicate the left triangle horizontally, rotate the muslin around such that the fabric’s breadth goes along the top horizontally. It is necessary to position the raised homespun fabric on top of the muslin on the right and in alignment with it.
  4. Look at the two mirror-image triangles and notice that the right angles are on the outside of the curtain and the shorter points are on the inside of the curtain. Draw a vertical line 7 inches from the inside edge of each curtain’s hem and measure the fabric’s length. Make a cut up the middle of the line.
  5. To begin, pin the homespun layers to their appropriate muslin layers and then sew down all sides, save for those that are wider than the cloth itself. Right-side-out each curtain through the aperture along its length. The edges of the fabric should be pressed.
  6. Each curtain should have the raw top edge of the width folded down an inch. Then, reduce the size by another three inches. To create a rod pocket, pin the fold and sew it in place. In a mirror image, lay out each curtain with the muslin side facing up.
  7. Make two marks 10 and 11 inches down from the top of the fabric’s outer edge. Starting at the bottom of the rod pocket hem, measure along the diagonal of the inside edge of the curtains and mark the diagonal edge at 10 and 11 inches. Connect the two 10-inch points and the two 11-inch points by drawing lines across the fabric. To create a channel, sew along the lines you’ve drawn.
  8. Measure the length of the channel by laying out the curtains again and putting them back together. To make the cording, cut two pieces that are this long plus four more inches. Only the muslin layer needs a one-inch-wide slit cut into it from the channel’s outer edge. In each curtain, thread one piece of cording all the way to the inside edge of the channel. To keep the cord in place, stitch over it about an inch in from the inside edge.
  9. Orient your drapes so that the home-spun cloth is facing the living area. To raise the curtain, simply pull the cord along the outside edge where it hangs out of the channel. Make sure the curtain cords can’t fit through the cut opening by tying a strong knot in the cording.

Make Prim Happen: My new Prairie Curtains! | Curtains, Primitive curtains, Country curtains

The Drip Cap

  • If you want to decorate your home in a primitive manner, finding curtains in the prairie style can be difficult because they are rarely sold in stores.
  • To figure out how long your cloth should be, multiply the length by 5.
  • Make two similar triangles from each cloth by cutting along the line.
  • It is necessary to position the raised homespun fabric on top of the muslin on the right and in alignment with it.
  • To begin, pin the homespun layers to their appropriate muslin layers and then sew down all sides, save for those that are wider than the cloth itself.
  • Then, reduce the size by another three inches.
  • Make two marks 10 and 11 inches down from the top of the fabric’s outer edge.
  • To keep the cord in place, stitch over it about an inch in from the inside edge.

What are the easiest curtains to make?

Tab top curtains are the cheapest and simplest to create. Panels created without header tape use less fabric since they are less collected.

How do I make my own curtains?

Making Your Own Curtains

  1. Measure. A lot of people know that the first step in any DIY project is to measure—and that you should definitely measure twice before cutting! …
  2. Cutter a piece of fabric…
  3. … Pin and stitch one side.
  4. Design and sew in an inner hem cuff.
  5. Sew the second side….
  6. Curtains can be flipped right-side-out…
  7. Create a rod pocket
  8. Iron.

How do you make easy unlined curtains?

Making Curtains Without Lining

  1. The fabric should be cut to the appropriate size, with side hem allowances of 10cm (4′′) and hem allowances of 20cm (8′′) on top and bottom added to the length. …
  2. Pin a 2.5cm (1′′) double hem on each side.
  3. Pinned the lower border with a double 7.5cm (3′′) hem
  4. Both of the bottom corners should be mitred.

How difficult is it to make curtains?

It’s simple to make curtains, but only if you grasp the fundamentals.

Because practically all of the sewing in curtains is done with a straight stitch, it’s a good project for people just learning to sew. There are, however, some fundamentals that must be learned before beginning to make curtains.

Is it cheaper to make curtains?

It’s not enough to save just a few bucks on your curtains; convenience is a major consideration in today’s society. Sewing your own curtain fabrics may be less expensive, but it takes a lot of time and effort.

What can be used instead of curtains?

Six alternatives to heavy drapes for a new look: blinding brilliance

  • Roman shades. Roman blinds have a timeless appeal, and because they take up less space than curtains, you may use more expensive materials. …
  • The panels of a curtain…
  • Close the blinds.
  • Film for windows…
  • Blinding with a matchstick…
  • Curtains for a cafe.

How can I make my curtains look expensive?

Make Your Curtains Look Expensive

  1. Extend the banners far and wide. For a more upscale appearance, place your curtain hardware as close to the ceiling as feasible.
  2. Make a statement with your equipment. Add thicker, more substantial hardware to your window curtains to give them a more luxurious feel. …
  3. Take their weight into consideration.
  4. They need to be taught.

Which way do you cut fabric for curtains?

A straight edge on your fabric is a must. Make a horizontal and vertical line with your marking pen by aligning your L-square along the selvage (vertical) edge. Straight edges can be achieved by cutting along the dotted line. Make sure all cuts are made along the crosswise grain of the fabric when working with solid textiles.

What kind of material do you use to make curtains?

There are many different types of curtain fabrics, but the most typical ones are made of cotton, silk, linen, polyester, velvet, acrylic, rayon, brocade, lace, or voile.

How do you make knotted curtains?

Place the folded edge of a sheer strand in front of a curtain rod and fold it in half widthwise. Pull the sheer strand’s ends through the fold and up the curtain rod’s back. To construct a knotted sheer strand, pull the sheer ends down and tie them together.

What means unlined curtains?

When compared to lined drapes, unlined drapes are lighter and less protective, but they have a few benefits of their own. It’s ideal for Summertime Breezes. Insulation isn’t necessary all year round.

Can you make curtains without lining?

Use a Sewing Machine to Make Unlined Curtains. Measure the fabric you intend to use. Just as with no-sew curtains, you’ll need to figure out how much of the window you want to cover before you begin sewing. To make the curtain rod loop, add six inches of extra fabric to the top of the curtains.

How much fabric do I need to make curtains?

One and a half to two times the width of the space to be covered is a good guideline for curtain length. The fullness of a heavier fabric can’t be achieved with a lighter cloth. Fabric that is lighter in weight necessitates more fullness.

How much narrower should curtain lining be?

In general, the curtain fabric should be 7.5cm (3′′) shorter than the lining. Because the thermal liner is so thick, it must be cut 17.5cm (678″) shorter than the curtain fabric to make a double hem. \

How wide should curtains be?

How Much Room Do You Need for Curtains? A combined panel width of 2–212 times the window’s width should be used to ensure that it seems wide and drapey when closed. There are few exceptions to this rule, such as if you’re only hanging curtains to frame a window and don’t plan on shutting them.

What is a wave curtain?

Because they hang from a thin, unobtrusive curtain rod, wave curtains can be used with any standard-sized window. A contemporary impression is created in any room thanks to their loose fold. Open-plan living and kitchen-dining areas are ideal for these pieces, but they look fantastic in any room.

How wide should curtains be for 36 inch window?

Using the previous example, if your window is 36 inches wide (36′′ x 2), you’ll need curtains with a minimum width of 72 inches, or two panels. If two panels are used, the breadth will be between 100 and 120 inches. Always round up to the nearest whole number. ”

How do you make two sided curtains?

Place a piece of one type of fabric right-side up on the table or work surface. Stack a second piece of the same sort of cloth on top of it, with the raw edges lining up with each other. Pinned them all together Sew the top edge with a seam allowance of 1/2 inch.

How much should I charge for simple curtains?

You can get a ballpark price by figuring out how much it costs to make a curtain, which can run anywhere from $10 to $15 an hour or $20 or more per panel. It might be a lot of work to make changes.

Can I use a blanket as a curtain?

The heat loss from your home can be considerably reduced by using thick drapes. To save money on curtains you’ll only use for a few months a year, make your own out of old blankets you already have.

Why are curtain so expensive?

Because they take so long and work to make, curtains may be quite pricey…. The price you pay for a pair of curtains depends on a variety of criteria, including the quality of the materials, the drop, the breadth, the labor time, and the personalization.

Are curtains in style for 2021?

Curtain trends for 2021 include creating an airy or light atmosphere. Curtains that are too thick can make a space appear smaller. … In order to stay up with curtain trends in 2021, consumers must limit the use of layers, ruffles and other decorative elements that take up a lot of space.

FARMHOUSE PRIMS: New Curtains instructions

How can I decorate my windows without curtains?

Get Rid of the Drapes: 15 More Eye-Catching Ways to Decorate a Window

  1. Item number 1/16. Stenciled Sign…
  2. The Rustic Privacy Screen. February 16, 2016.
  3. 3.16 inches of frosted glass design
  4. 4/16. Faux Stained Glass.
  5. Linens for tablecloths. 5/16.
  6. Shutters in the style of old-fashioned shutters.
  7. 7/16. Glass Shelves for Windows…
  8. Windowpanes in lace. 8/16.

Is it OK not to have curtains?

That’s the only time it’s appropriate to use it. When there isn’t enough space for it. There’s no better place to express yourself than at the place where you call home. Do not hang curtains if they are not your cup of tea.

How do I make my curtains look professional?

Count on us for foolproof curtain-hanging advice and instructions.

  1. Hang ’em high! If you have a low ceiling in your room, make sure to hang your curtain rod as far up as possible. …
  2. It’s best to spread them out….
  3. These should be hung just so….
  4. Hang the appropriate number of panels….
  5. Hang a panel that matches your decor.

Which color is best for curtains?

  • It conjures up images of aristocracy and sophistication when the color gold is used.
  • Make your bedroom pop with royal blue accents….
  • Curtains in pink and white for your child’s room….
  • The classic black-and-white look never fails to wow….
  • Curtains in gray to complement a gray home…
  • To soften the overall appearance, use teal curtains.

How can I make my curtains look good outside?

How to Make Your Curtains Look Attractive from the Exterior

  1. Transparent glass is an excellent choice for windows.
  2. Choose Patterns That Are a Little More Eye-Catching….
  3. Check to See if Your Curtains Provide a Good Contrast….
  4. Eliminate Clutter Around the Window’s Peripheral Area
  5. Maintain the cleanliness of the curtains.

Conclusion

As a result of reading this guide, I hope you now know how to make your own set of prairie curtains! The process is straightforward and simple.