With a drapery hook affixed to the top back of your curtain and the correct size, you can easily hang your curtains. Let’s take a look at some of the most common methods for using drapery hooks on standard drapes.
Hanging your drapery using old-fashioned hooks can seem a little outdated. But it is a rather fundamental skill that you need to master. Fortunately, the concept of drapery hooks is simple enough to grasp.
Drapery hooks
Step 1: Choosing the right size
If you’re looking for an old-fashioned way to hang your drapes, you might want to look elsewhere. You must, however, learn this fundamental talent. Because drapery hooks are so simple to understand, it’s a good thing.
Drapery rings with built-in metal or plastic eyelets are a must-have accessory to help you hang your drapes. Simple curtain rings can be transformed with a coat of spray paint or a ribbon bow.
Step 2: Mark the curtain
The term “ordinary curtain” refers to any curtain that you have in your home, such as a shower curtain. Sewing in the bottom of the hemming is necessary for both rod pockets and rear tab curtains. We may now discuss how to hang ordinary curtains with drapery hooks.
To make it easier to work with, place your fabric with the front towards the table. Take note of where the curtain’s top edge hemming joins the bottom edge of the fabric. Mark the locations of each drapery hook on the wall with a pencil and a measuring tape. In order to keep the curtain in place, the distance between each hook is crucial.
Using back tab curtains, you can attach the pins directly to the fabric tabs. Marking the pin positions and fabric measurements can take time.
Step 3: Insert the pin.
Hook up your drapery hooks and pin the straight edge to the cloth. Moving your pin hooks an inch below or above the typical height attachment will allow you to alter the natural length of your cloth.
Xem thêm : How To Hang A Valance And Curtains? Complete Step-by-Step Guide
Use a drapery hook to attach the cloth to the rear of the curtains. You don’t want to slam it right in the middle. The curtain’s appearance will be ruined if the pin is seen. Secure the pins in place and make sure to attach them at the same height throughout.
Step 4: Hang the curtain
Pin the drapery hook to the fabric’s backside. Do not push this all the way in front of you. Because else, the curtain’s beauty will be ruined by the pin’s visibility. Maintain a consistent height and position for all of the pins.
Get your curtain rings and drapery hooks ready to go. If done correctly, the drapery hook curve should protrude from the fabric, with the straight edge holding it in place.
The eyelet on your curtain rings is the perfect place for the drapery pin. Alternatively, you can attach it to the ring if you don’t have a suitable eyelet. If the circle is too thin or thick, the hook won’t be able to secure itself to the surface. Hang the rings from the bracket using the rod and rings.
Curtain weights
To improve the flow and appearance of their draperies, some people use curtain weights. If you want to give your drapes a more polished look, this is an excellent method to go about it.
Curtain weights can be added to the bottom of your curtain to keep it in place. Sheer curtains and other thin, airy fabrics are ideal candidates for this method. While drapery weights can help keep draperies in place, you must be careful.
Even the smallest drapery hooks can only support a limited amount of weight. For those times when you need to add heavier drapery weights, there are various medium-sized hooks available.
Use a seam ripper to install them. The weights should be evenly distributed along the seams of the curtain when it has been opened from the bottom. Make little pockets at the rear of the curtain to keep the weights from shifting around.
Why use drapery hooks
Xem thêm : How To Hang Back Tab Curtains With Clip Rings? Step by Step Instructions
One of the oldest and most conventional methods of hanging drapery is to use drapery pin hooks. Hanging drapes have been around for a long time and aren’t going anywhere anytime soon. Fortunately, drapery hooks are a breeze to put in, and they’re just as effective as more complicated curtain gear.
Drapery hooks for ordinary curtains are simple to use once you get the hang of it. You’re ready to go as soon as you have the proper tools and equipment. Using it, you won’t have to stress about figuring out other confusing curtain hardware in order to hang stunning drapes.
Drapery Pin Hooks, They’re Not Just For Your Grandma’s Curtains
HOOK, LINE, AND SINKER
Grommets are sewed into many of the curtain panels on the market today. Grommets work nicely with a variety of carriers and curtain tracks, so if you like the aesthetic, go for it! Many people, on the other hand, are loyalists to tradition and the retro aesthetic. The drapery pin hook is an oldie but a goodie in the drapery hardware world whether you have a set of curtains without grommets or if you want to build your own curtains from a fabric you adore. They are still rock stars in the drapery industry, and we’re going to show you how to use them in your own house.
HOOK UP
Drapery pin hooks can be used with a normal rod-pocket curtain panel, according to a recent article on SFGate’s website. We don’t advise the use of poles, but their advice about pleats and hooks is spot on. In order to attach hooks to a curtain panel, all you need to do is poke a pin through the curtain header. The top hem is made up of several pieces of fabric; if you insert your pin hook solely through the back piece of cloth, the hook will be hidden. Non-pleated curtains are ideal for this arrangement.
PICK YOUR PLEATS
To get traditional pleats, our customer care department may make them for you on your preferred fabric or show you how to do it on your own with our in-depth instructions. Traditionally, buckram is attached to the top of the fabric-to-be-curtain by sewing it to the hem. An adequate amount of rigidity is provided by buckram, which allows the fabric to be pleated in a wide variety of ways (by hand or machine). In order to keep the curtain in place on the track, you insert the sharp end of a 4138 Drapery Pin Hook into the pleat’s seam (via a carrier). It has been the industry standard for years, and this stainless steel hook will endure pretty about indefinitely without staining your curtain. If you’re looking for a simple curtain hook, our 4146 Drapery Pin Hook is a great option.
Pleated drapes hanging with drapery pegs are conventional to some, but not to others. You may still want to use drapery pins to hang your curtains even if you don’t like the pleating. If you want to use a traverse rod, you can do it with the help of drapery pins.
How to Use Drapery Pins Alone
Simply slip the pins into the top of the curtain for the quickest and easiest method of hanging drapes. If your curtain has a liner or a well-sized rod pocket, you can get away with this. Keeping your drapes from drooping at the top is a matter of placing your hooks closely enough together.
- Find out the number of drapery pins you’ll need. One pin every 4 to 6 inches is usually sufficient. A greater number of pins may be required for delicate fabrics.
- The back of your curtain should face up.
- Start at one end of the curtain and indicate the pin spacing with a pen or pencil. Rod pockets are preferred, however if the header is tall enough to fit your pins, you can use it instead.
- Slide your pins into the fabric slightly above the hem of your pocket or header. Make sure that the pin goes through the rod pocket from the back and comes out the top of the pocket when you do this. Put the pins through only one layer of fabric; they should not be seen on the front of your curtain.
- Every time you take a measurement, mark a new interval on your curtain and repeat the process.
- Drape the curtain pins over the curtain rod, or feed them into the hooks of your traverse rod, to secure the curtain in place.
How to Use Pins and Pleat Tape
When using drapery hooks to hang your curtain, you may notice that thin or soft curtain fabric hangs strangely. Pleating tape and pleating pins can be used to stiffen the curtain’s hem. Pleating tape is an option, but you don’t have to use it to create pleats to your draperies. Drapery pins can be installed more quickly and easily with its help.
- The back of the curtain should be facing you.
- Cut the pleating tape to the same width as the curtain.
- Using the pleating tape, attach it to the top of the curtain in the desired position. Pin pocket apertures on the tape should face down toward the curtain’s base.
- Pleating tape should be sewn into position along the stitching line. To avoid a crooked seam and closing any pin pockets by mistake, stay on the line when sewing.
- Pleating pins can be inserted at specified intervals into the pleating tape by sliding them into it. The pleating tape features little pockets where pins can be inserted. Pleating pins, unlike conventional drapery pins, do not have sharp pointy edges, making this a critical consideration.
- Install the tip of a pleating pin into a pleating tape pocket to create a pleat in your draperies if desired. Plié the fabric away from your body by pulling it apart at the sides. Using the pleating pin, make the pleat to your desired size and then slip the opposite side into position to secure the pleat.
- Install curtain hooks without pleating or continue forming pleats across the curtain’s top. Continue this process until you’ve covered the entire draperies.
- Drapery pins can be looped over the curtain rod or installed in a traverse rod to hang the curtain.
Nguồn: https://iatsabbioneta.org
Danh mục: Curtains
