Updated at: 31-05-2022 - By: Sienna Lewis

Formal décor calls for pinch-pleated draperies. With opaque or lined drapes, the window treatment is heavier. Drapery can be suspended from a traverse rod, which is made of metal, a pulley system, and nylon gliders. Using curtain pins that may be attached to the header of drapes, the heavy drapes can be easily opened and closed by sliding them on the gliders that slide down the metal track. It takes two steps to hang pinch-pleated curtains from a traverse rod. In order to hang the drapery, a curtain pin must be attached to each drape, then the glider.

Installation of the Drapery Pins

Step 1

Make sure the drapery panel is laid out on a flat surface, right-side up. Using one hand, hold the drapery pin and the panel’s header in the other. The drapery pin’s pointed end should face upward.

Step 2

Insert the pin’s sharpened point immediately under the tack on the drape’s left side where the pleat is tacked or sewed. Make sure the pin’s point is facing the top of the header when not in use. Take a pin and slide it under the tack until you reach the first bend of the pin.

How to Hang Curtains: An Easy 4-Step Guide (Plus Styling Tips) | Architectural Digest

Step 3

Continue pinning the panel with drapery pins by attaching one to each pleat as you make your way from left to right.

Step 4

Drape the second panel in the same manner.

Hanging the Drapes

Step 1

Count the number of curtain pins on the drapery panels to make sure the traverse rod has enough sliders to accommodate them. Sliders can be added or removed as necessary.

Step 2

The last drapery pin on the left panel should be inserted into the traverse rod’s left-most slider. The pin’s hook opens downward, and it goes through the slider’s bottom hole.

Step 3

The pins should be inserted sequentially, starting from left to right, one at a time.

Step 4

Repeat this process for the second drapery panel to be hung.

How To Hang Curtains On A Traverse Rod? 9 Easy Steps To Follow!

Trying to figure out the best way to hang drapes on a traverse rod?

It’s not just about the curtains when it comes to deciding on your window treatment.

You’ll also have to figure out a few other things.

Rodding is one of them.

Rodding should be chosen based on your curtain fabric, window type, and personal taste.

Besides that, you need to decide whether or not you want to hang your curtains this way.

Grommet curtains with decorative rings and poles can work well in some windows, but traverse curtain rodding is needed in others.

In this piece, we’ll discuss how to tell if you need a traverse rod.

We’ll also show you how to hang your drapes on a traverse rod as well.

So, be on the lookout for more updates!

What Curtains To Use With A Traverse Rod? - Home Decor Bliss

Knowing A Traverse Curtain Rod

The first step is to familiarize ourselves with the concept of a traverse curtain rod.

You can use either clips or eyeballs to move within a slot in the rod’s end.

Curtain pins can be inserted into the tiny openings in its eyes.

These peepers will follow the curtain rod like a beady trail.

The length of a rod will determine the number of eyes it has.

The curtain rod also has a string running through it. The main pulley or slide is where it is fastened.

To open and close the curtains, you’ll need to utilize this cord, which extends over the rod.

Hooks and pins are stitched into some custom-made drapes designed for traverse rods.

You may also require drapery pins if you’re using a traverse curtain rod.

Steps To Hang Curtains On A Traverse Curtain Rod

Here are the steps to hang your curtain on a traverse curtain rod, now that you know what it is.

How to hang curtains on a traverse rod is as follows:

Step #1. Inserting a drapery pin

To begin, insert a drapery pin into the fabric.

This should be done at the back of the curtain, in the center of each pleat.

Leave the hook end of the pin facing outward while inserting the straight end into each pleat.

The hook must be curved downward as well.

Step #2. Repeating the process in every drape

The pin must now be inserted behind each drape.

Step #3. Begin with the master overlapping carrier

If the drape is closed, this phase is responsible for overlapping one side of the drapes over the other.

Start at the back of the master overlap carrier and hook the first pin into the arm of one curtain panel.

Step #4. Insert the second pin into the arm base

Start from the beginning this time around.

It will form a soft fold on its upper arm.

Step #5. Insert the remaining pins into the slides

Except for the last two pins, perform this step sequentially.

The rod’s end should now have a spare slide attached.

Step #6. Now slide the last pin into the rod’s hole

The final pin must be inserted into the hole on the bracket.

Step #7. Repeat the process

Continue with the same steps from steps #3 to step #6 on the second panel.

Please hang it on the other side of the curtain rod while you do this.

Step #8. Making a vertical crease

Cease the material in between each pleat with a vertical crease.

The crease in your curtains can be checked by opening and closing them repeatedly to see if it reappears each time.

Step #9. Open the curtains again

To create a beautiful wave in the curtains, first pull the pleat and the fabric forward, then push its centre backward.

The 5 Best Curtain Rods (2022 Review) - This Old House

When To Use Traverse Rods?

If you require a curtain that can be opened and closed, traverse rods are a wonderful option.

To open and close the curtains with standard rings and rods, you’ll need to use your hand. It’s a pain, and the fabric gets stained as a result.

You can rapidly close and open your curtains using traverse rods that have a string.

When using lengthy rods, it’s often necessary to add a support bracket in the middle.

Your curtain won’t be able to fully close in this manner.

You’ll be able to open and close your patio sliders, French doors, and huge windows with ease if you install traverse curtain rods in them.

In the event that you wish to use sheer curtains as a base for heavier ones, or if you plan to use them with a valance, you’ll need two rods.

Instead of using two curtain rods, a double traverse rod can be used.

It will conceal the functioning components, resulting in a less crowded final product. It can also give you a layered appearance.

It’s A Wrap!

A traverse curtain rod is one of the most heavy-duty types of curtain rods available.

It has a cord and a pulley system built in, making it simple to close and open your draperies.

When you first get your hands on this piece of gear, you may not know what to do with it.

You’ll appreciate the convenience of traverse rods once you’ve learnt how to hang curtains on them.