The correct drapes and curtains may transform the look and feel of your entire house.. You may learn how to take accurate measurements for your home’s window treatments in this step-by-step project guide. Pick out how to locate the hardware, measure the breadth, length, and find the appropriate curtain rod by reading on.
Decide Where to Hang Hardware
You’ll first need to decide where you want your drapes to hang. Depending on where you want the drapery rod to be installed, the length of your drapery will be determined.
Bạn đang xem: How To Measure Curtains? Complete Step-by-Step Guide
The bespoke draperies are hung from the outside of the windows. The following are some helpful hints for dressing your windows so that they appear larger when they’re closed and show more of the window when they’re open:
- Place the pole 8 inches above the window if you have the room.
- Have the rod extend 12 inches on each side of the window, 24 inches total.
Extend the rod by 12 inches on each side of the window, for a total length of 24 inches.
- To prevent the curtains from extending past the window opening, double-check your measurements.
- The fabric begins at the top of your rod, so measure from there for correct, full-length drapes. Refer to the rod instructions for more information.
Once you’ve decided on a location for your drapery hardware, you’ll need to determine the height of your rod from the floor:
- Make a note of where you want to hang the drapery rod before you begin.
- The fabric should hang from the lowest point possible (either the floor or the bottom of the window). It’s the distance from your rod to the floor.
- Your drapes will need Rod to Floor Height dimensions, however you must wait until your curtains arrive before you can hang any hardware.
Choose a Curtain Type
Consider the style of drapery you desire before learning how to measure your curtain’s width. A window’s side panels can be dressed up in a variety of ways. Closed-to-the-wall curtains can also be an option. The number of drapery panels you require will be determined on the style you choose.
Tip: Make sure the fabric for your custom drapes has the right amount of fullness. Order your drapes to the precise width you require.
Measure the Width
If you’re making drapes or curtains, you’ll need to know how wide the panels will be. If you want the entire window to be covered by your curtains, follow these instructions:
- Measure the width of your window.
- Your window’s width has to be measured.
- In order to figure out how many drapery panels to order, divide your entire width by your total number of drapery panels.
- You should order enough custom drapery panels to cover the full space you intend to drape (total width divided by panels). For example, for a 60-inch window with two curtain panels, add 24 inches to 60 inches (window width) and divide by 2 (number of panels) to get 42 inches. Each of the two requested panels must be 42 inches wide minimum.
Side panel window coverings have a slightly different width measurement than standard window coverings. It is not necessary to close the side panels. In addition to framing, they can amplify the size of a window. Decide how wide you want the panel on either side to be.
Measure the Length
The style you’re going for will dictate the length of your curtain or drapes.
- Outside-mounted drapes in the valance style provide the illusion of a taller window. Sizes range from 10 to 30 inches in length.
- Ensure that the length of a sill-style curtain will terminate 3/8 inch above the window sill. For windows with sills that extend past the opening of the window, we propose sill-style drapes.
- Draperies of the cafe design can be installed either inside or outside, and they are most commonly used in kitchens. Choose a length that is 6 inches below the bottom of the window, or 3/8 inches over the window sill, for a cafe-style window covering. The drapery hardware should be placed in the centre of the window for this look.
- For exterior windows, apron-style drapes should fall between 4 and 6 inches from the window sill or the bottom of the window.
- The length of floor-length draperies should end 3/8 inches above the ground. This form of drapery is most usually used with an exterior mount and is recommended for any drapery that may be operated on a regular basis.
- In rooms where precise mounting is required, such as a ceiling mount that drapes to the floor, the sweeping, brushing, or cuff length drapery design is commonly utilized for outside mount windows. For this, a length of 1 to 3 inches longer than the distance from the rod to the floor is recommended.
- The pooling or puddling style draperies can be utilized in outdoor mounts to disguise uneven floors or to give some flair to your decor. If you don’t frequently open or close your windows, we recommend this type. Add 6 to 12 inches to your Rod to Floor measurement for this style (Step 1).
- Find a Curtain Rod That Fits Your Window
- Fifty-two inches can be added to each end of a curtain rod with finials and brackets. To get an accurate measurement, look at your finial alternatives.
- To make sure your rod and finials are exactly the width you ordered, we’ll make some deductions.
- Brackets will keep your drapes from going over the top.
With the appropriate curtains, you can complete the look of your home. It’s easy to transform a room with curtains that are hung correctly. Make sure your window’s width, length, and height are all accurate. Don’t forget to choose a curtain rod that matches or accents your decor. Shop for all of your hardware and window treatments needs in one place! Deliveries from The Home Depot can be made at any time and in any location.
Choosing the right size curtain pole
A curtain rod or track already installed is an added bonus.
Measure the width of your window and add 30-40 cm if you need to install one. Your pole or track’s width will be determined by this measurement, which will guarantee that your window is adequately protected on all sides. Install this in the middle of your window, about 15 centimeters above the sill.
Before drilling or installing anything into the wall, double-check that there aren’t any hidden pipes or wires.
Measuring Curtains
The first step is to figure out how much space you’ll need. You should measure the entire length of the curtain pole or track, omitting any finials or fixtures on either end. For pencil pleat, tab top or eyelet curtains, double this width measurement to account for the way the curtains are gathered at the top. Finally, to ensure that your curtains close properly in the middle, add an inch or two to the width measurement.
Decide where you want your curtains to hang before you start measuring for length. You will need to take your measurements in a different way depending on the type of curtain you are hanging.
On a pole, measure from the eye of the curtain ring at the bottom to where the curtains will hang.
Measure the distance between the top of the curtain rod and the desired end of the eyelet/ring/tab top.
If you want your curtains to terminate at a certain point on your track, measure that distance.
Checking and double-checking your dimensions will give you peace of mind that the drapes you purchase will fit your window perfectly.
All Shaws Direct curtain measurements are provided for each individual piece of fabric. Every single curtain panel is measured in inches. Every pair of our curtains is sold as a complete set.
Xem thêm : How To Install Curtains Over Blinds? Complete Step-by-Step Guide
As order to avoid confusion, voiles are exclusively sold in singles, not pairs.
Measuring your curtain drop
Curtains that graze the sill should have an extra 12 inch removed from their overall length.
Curtains that sit below the sill: These measure around 15cm in length.
The length of the curtains should be reduced by 12 inch so that they fall just above the floor.
In order to get your curtains to gather on the floor, you’ll need to increase the floor measurement by 15-20 centimeters.
Steps To Measure Curtains
Who wants curtains that are either too short or too long?
The process of measuring is a prerequisite in almost all aspects, including the planning of your curtains.
The act of measuring is a precondition in almost all elements, including the planning of your curtains.
Even when planning your curtains, measurement is a necessary part of the procedure.
Step #1. Choose your preferred mounting
The manner you hang your curtains will largely influence their length and width.
There are two ways to hang your curtain in this article.
External to the frame mounting
Every home we visit, including our own, uses this method of hanging curtains.
This kind of attachment is exterior to the window frame, as the name suggests.
So it is understood that the rod is held on the wall.
As a result, it is clear that the rod is secured to the wall.
An additional illusion that it can create, though, is that of a taller ceiling.
Furthermore, drilling screws into the window frame will not damage the frame if the rod is not mounted there.
Internal to the frame mounting
For whatever reason, this mounting method has a distinctive effect on a certain area. Doing so provides the impression that the windows in your home are larger than they really are.
Instead of blocking your window completely, this method allows for a small amount of light to pass through it. Distinctive people should use this strategy instead.
If you’re living in an apartment, you can just stick the curtains to the wall because they won’t survive long.
Step #2. Measure the rod size
Curtains can be hung in a variety of ways, but the most frequent and easiest method is to use a rod.
One consideration is the length of the rod.
When determining its dimensions, the window’s width should be multiplied by 4 to 6 inches at each end.
Xem thêm : How To Make Bamboo Curtains? Step-By-Step Guide
This length is neither too short nor too lengthy, so it’s just right.
There should be just enough to completely cover the window.
Also, keep in mind that you’ll need a sturdy rod that’s thick enough to keep the curtain rod from bowing in the middle due to its weight.
The rod should be installed below the trim mount if you want the window frame design to be prominent.
Step #3. Curtain length preference
When it comes to the design of our home, we have a clear vision in mind.
In order to make our home appear its best, we must decide the length of the curtains we intend to employ.
A meter stick or a measuring tape can be used to determine the length of the curtains. Take a measurement from the rod to the desired location.
Hang your curtains to the length of your window frame if you choose.
To accomplish this, you’ll need a curtain that extends from the rod to a point 1 centimeter below the window sill.
Using curtains that measure from the rod to 20 cm below the windowsill is an option if you prefer a longer curtain.
Now, if you want your curtain to fall to the floor, keep in mind that a curtain that is too lengthy isn’t ideal.
Purchase a rod that extends from the rod to a distance of one centimeter above the floor.
Step #4. Determine the curtain width
Using a measuring tape or meter stick, measure the width of your window once more.
Afterwards, multiply this figure by 1.50. The right curtain width can be calculated from the smallest possible width up to a maximum of three.
Your window will be covered by all of these ranges.
Of course, the breadth of the curtain pleats will have an impact on how they look.
That’s all there is to it, guys! That’s how you measure your drapes appropriately.
For more articles, you want to read this to know how to measure your window for a curtain.
To learn how to measure your window for a curtain, check out this post.
Final Words
I hope you’ve learnt how to measure curtains at the end of this essay.
May the words above lead you in the right direction.
As far as I’m concerned, I couldn’t have done it without you. Thank you so much for your time and efforts!
Nguồn: https://iatsabbioneta.org
Danh mục: Curtains
