Updated at: 09-08-2022 - By: Sienna Lewis

Swag and jabot curtains can be made in several ways. This question will be answered at the end of this post.

There are numerous methods to customize swags and jabots.

Knife pleats turned outward are the most popular design.

Nine to fifteen inches wide is typical for jabots. To the inside, they gradually get thinner.

A third of the width of your window treatment should be covered by it.

The jabots’ lower point must be lower than the swag’s center point.

You can experiment with different kinds of gathers and pleats when making jabots.

Because there are no rules, you can be as creative as you want.

The only thing you need to think about is the size of your window.

What Are Swag And Jabot Curtains?

The simplicity and elegance of a swag window covering can’t be overstated.

Basically, this is just a piece of fabric stretched over a window-frame-mounted pole.

It is common for people to wear swags as a kind of decoration. They can make your window’s geometry appear softer.

Either leave simple swags untrimmed or add some fringe.

How to make a Jabot - YouTube

The tails of the cloth cascading down the window sides are known as jabots if they are woven into the fabric. An informal look can be achieved by combining the two.

It is impossible to draw Jabots, hence they cannot be used for privacy. Instead, they’re there to add some flair to your blinds or panels.

However, they can also be utilized as a standalone window covering.

Wedges, rectangles, and plain squares are just a few of the different ways they can be sewed.

Line them with an accent or the same fabric used for the jabots.

The jabots can be mounted on a pole or a board, depending on your desired look.

What Are The Materials Needed?

Before we get started, let us know what items you’ll need for the operation. Make sure to prepare these first before you start.

  • Before we get started, let us know what items you’ll need for the operation. Make sure to prepare these first before you start.
  • First, let us know what items you’ll need before we begin the procedure. Ensure that you have these in place before you begin your project.
  • Fabric with a strong visual contrast
  • A base for attaching the board
  • a set of hardware and installing gear
  • Staple gun for heavy-duty use

3 Steps To Make Swag And Jabot Curtains

You may now begin making your swag and jabot curtains once you have gathered all of the necessary supplies.

Then, how do you manufacture swag and jabot curtains?

This is how it’s done.

Step #1. Deciding for the size of the jabot

Determine the finished length of the jabot before you begin.

At least four to ten inches plus the depth of your mounting board should be overlapping the swag’s ends.

Decide on pleats as well. Determine the appropriate width and the required number of pleats.

That’s not all; you’ll also have to decide on the jabot’s drop.

Step #2. Making the pattern for the jabot

Mark the fabric to the desired finished length of your jabot using a marker.

After that, take a measurement down the mounting board from the apex.

To make a right angle, make a second line perpendicular to the first one.

The finished jabot’s inner length should be measured next.

Pleats should be placed at the top of the garment, between the precious lines.

Make a swatch from the pattern by cutting it out. After that, you can make any necessary alterations to the pattern’s measurement.

Step #3. Making the jabot

Cut the left and right jabots according to the pattern you made in the previous stage.

All seam allowances should have a half-inch added to them.

You can cut two jabots together by layering the two fabrics with their right sides together.

You can make two jabots by laying the two fabrics right sides together and cutting them.

Begin sewing the lining and the main fabric together with their right sides facing each other, excluding the top where you marked for the pleats.

Press the edges once the right sides have been turned out.

You may also add little cording to the edges of your jabot to give it a more polished look.

You’ll be able to press your seams more effectively with this as well.

Make sure the curtain’s top edge is straight before folding and pinning the pleats.

It’s also important to ensure that the pleats’ sides and the top edge meet at a proper angle.

When you’re done with that, get the tail.

Pin it to the top of the board, or to the jabot itself, using the pencil line on top of the board.

It must be aligned with the corner of the mounting board.

If required, make alterations.

Press the pleats if you want a more formal look.

Leaving them loose is an option if you want a more laid-back look.

Attach the opposing jabot to the mounting board in the same manner.

EASY Swag tails (jabots) anyone can make! - YouTube

How do you make a swag curtain?

The first step is to hang one end of the swag over the rod’s end. The other end of the swag should be draped over the pole at this point. Allow the middle piece of fabric to fall to the ground. If all goes according to plan, the draped fabric in the middle should resemble a standard curtain swag.

How do you calculate fabric for swags and tails?

2 yards of fabric will be needed for each swag, which is an average of 44 inches wide. Double the longest length, add 4 inches, then divide by 36 to get the jabots length. For a single pair of Jabots, you’ll need this many yards of fabric.

How do you make a window swag?

What You Need to Know About Sewing Window Swags

  1. Measure the distance between the ends of the curtain rod or swag knobs and the width of the window….
  2. … Cut a piece of cloth that is 24 inches wide and the desired length from the fabric that you measured before….
  3. Prepare your work surface by laying the fabric right-side up on it…
  4. To keep the fold in place, sew a straight stitch along the fold.

How do you measure for fishtail swag curtains?

  1. If you have a drop, measure the width of your window.
  2. The outside fabric and the lining should have been prewashed and pressed before cutting (per our example). …
  3. To draw a straight line from one corner to the other, measure 16 inches from the fold (NOT the fold). …
  4. When laying out your textiles, put them face to face.

How long should swag curtains be?

A 45-inch swag’s top edge takes roughly 2 yards of fabric as a general rule of thumb. If you’re unsure of how much fabric you’ll need for your project, you can use an online fabric calculator or pattern envelope to figure out how much fabric you’ll need.

How do you hang a swag curtain without a rod?

Hook eye screws can be used to hang pleated curtain panels without the need for a curtain rod.

  1. Drapery pins should be inserted across the top of the curtain panel.
  2. The distance between the pins should be noted when determining the curtain’s width along the top edge.
  3. Make a pencil mark on the window to indicate where the pins should go.

How do you measure fabric for swag curtains?

Using a flexible measuring tape, trace the arc of the swag from the top of the pole on the left-hand side to the top of the pole on the right. This is how much swag you have. To gather the right amount of fabric, you must measure the swag’s lowest point.

What makes a good swag?

Cotton and polyester blends are ideal for canvas swags. This results in a breathable, rot-proof, and water-resistant cloth. The addition of nylon to the ripstop weave results in an even greater strength-to-weight ratio.

How long should Jabots be?

Using the mounting board as a guide, measure how far down from it you want the jabots to fall. This is typically one-third of the whole length of the drapes or windows.

How do you hang swags outside windows?

Swags for Outside Windows

Instead of a wreath, use a swag on your front door or on the window ledge of your window. You can hang the Christmas swag from the window sill using cup hooks or a suction cup hook on the glass, depending on the size of your swag.

How do you wrap curtains around a rod?

Using a Scarf to Cover a Curtain Rod

  1. Fold the sheer in half and lay it out flat….
  2. A large binder clip or a piece of masking tape can be used to secure the sheer to the curtain rod….
  3. Binder clip one end of the sheer to the curtain rod and then the other.

Who bought out Country Curtains?

The Country Store of Vermont

This decision was made in October 2017 by shareholders of Country Curtains, who voted to liquidate the firm at the end of 2017. The Vermont Country Store bought Country Curtains’ designs in February 2018.

How do you make a cravat?

How to Make a Cravet

  1. The first step is to gather the necessary materials. Your local fabric store should have what you need:…
  2. 2nd Step: Purchase a Pattern or Create Your Own.
  3. Cut your fabric and lay it down on a work surface.
  4. It’s time to tie the knot!
  5. 5: Sew the Tie End….
  6. It’s time for the collar.
  7. This is the final step in making the collar.
  8. Gather the ends of the ties.

How do you hang swag curtains with knots in corners?

In order to ensure that the curtain and swags are hanging evenly on both sides, adjust them. Grab the curtain at the end of the drapery rod with your free hand. To make a loose knot, fold it in half and draw the hanging end through the loop.

How long should tier curtains be?

There are two standard lengths for tier curtains: 24 inches and 36 inches, depending on the width of the window they’re intended to cover. A curtain’s length is determined by how much fabric there is above its rod pocket, not how much fabric there is below it.

What does tier mean in curtains?

When it comes to window treatments, tiers are fabric panels that cover only the bottom half of the window and are usually paired with either a valance or swag on top. With tiers, a room appears more informal and comfortable.

How To Make Swag And Jabot Curtains? 3 Easy Steps! - Krostrade

How much wider than the window should a valance be?

If the valance is hanging by itself or over a Roman shade, it should only be 1-1/2 to 5 inches broader than the window. In order to fit over a pair of custom curtains, it should be 10 to 30 inches broader than the window. This should be about two to three times the width of the window if the valance is fully collected.

What can I use instead of a curtain rod?

Rods made of pipe. This is a rather typical alternative to the previous one. Many individuals use copper pipes as a substitute for a curtain rod when they need one. Many people are drawn to copper pipes because of their distinctive appearance, but any type of pipe will do. Tuesday, August 22nd, 2021

How can I hang curtains without drilling holes?

Begin by putting your drill and spackle away.

  1. 3M Command Hooks are the best way to hang things.
  2. Curtain rod brackets like those from Kwik-Hang are a good option.
  3. Utilize curtains with tension rods.
  4. Get Creative With Coat Hooks.
  5. Use Coat Hooks to Your Advantage.
  6. Using this method, you won’t damage your walls when hanging curtains.

How wide should a valance be for a 36 inch window?

The Window Treatment Expert website recommends adding 2 to 4 inches to the width of a valance for a 36-inch window, with less for narrower windows and more for broader ones. If you have a 36-inch window, the valance will measure between 40 and 44 inches wide.

How long should a window valance be?

The valance’s length should be equal to one-fourth of the window’s height plus one inch. Use these measurements to help you cut a rectangle out of both your outer fabric and inside lining material. Make sure that the fabric and liner are placed right sides up.

How many yards of fabric do I need for a window valance?

The obvious answer is that it varies, but a typical 36- to 40-inch window will require anything from 1-1/2 to 5 yards of face fabric. 2-1/2 to 8 yards of face cloth are a reasonable estimate for double-wide windows (70 to 80 inches wide).

How can I make swag more comfortable?

Tips for Staying Comfortable

  1. How to Remain at Ease
  2. 2 Add some flavor to your swag.
  3. For the third step, using foam tiles.
  4. Use a stretcher….
  5. 5 Open a window if possible.
  6. Keep your head warm by wearing a beanie 🙂
  7. 7 Use a car sun shield as a thermal pad. …
  8. 7 Use a car sun shield as a thermal pad. …

How to Make a One-Piece Swag and Jabot Draped Over a Rod

Use a sun shield from a car as a thermal pad….

7 Use a sun screen from a car as a thermal pad….

Determine the length of the jabot on each side. Using a tape measure, measure the length of the left jabot from its bottom to the rod, across the rod, and back down to the length of the right jabot.

Using the measurement from Step 1 plus one inch, cut your 54- or 60-inch wide fabric to that length.

Match the breadth edges of the fabric when you fold it in half. Lay the fabric out on the table with the fold on the right side of the table. Make a mental note of the top left corner as “1,” the bottom left corner as “2,” and the bottom right corner as “3.” Place a mark on the fabric 12 inches up from the cloth’s lower left corner, corner 2, and the length toward corner 3. When you get to corner 1, draw a line from this mark and cut on the line. Cutting a triangular form out of the fabric’s end is what you are doing.

Fold the fabric in half and open it out. Then, turn the edges over 1/4 inch and press them again. The second fold should be sewn close to the needle.

Take a piece of fabric and fan-fold it. Make use of the help of a friend or family member to ensure that the box is neat and well-folded. While you work on one end of the fabric, your helper mirrors your folds on the other end. Count 4 inches from one short end of the length and fold it in half wrong-sides-up. Fold the remaining fabric in half, right sides together, and then in half again, wrong sides together, for a total of four inches of folded fabric. Finish by fan-folding the fabric in the same way as the first layer, the sewn edge facing in the same direction as the fold.

The center of the folded package should be marked.

The center of the package should line up with the center of the curtain rod when you raise the package. When you’re done, you’ll have a flat package that has the jabots extending down the rod’s backside. There is a long section of fabric on this top layer of the box, which is why it’s the last one you folded.

It is best to let a portion of the swag fall below the rod until it reaches the desired spot.

Lift the top layer of the fabric up where the cloth meets the rear of the rod to create the swag look. Layers can be lifted a few inches and gently tugged away from the rod. Pull both ends of the rod simultaneously. Lifting and yanking the fabric into a swag fills up the space between the cloth’s top and the rod.

Once the top layer has reached the rod, continue raising and dragging it until it has completely covered it.

Slightly reposition the jabots; they’ll have been separated during the process of making your clothing..

It’s A Wrap!

Finally, you’ve finished your work!

Making swag and jabot curtains shouldn’t be that difficult, right?

You can have the window treatment you want as long as you follow the instructions.