Updated at: 09-03-2023 - By: Sienna Lewis

In this article, we’ll discuss the motor on an okin recliner and how to fix it. This is the manual you need if your engine has stopped working. These are some of the most frequently encountered motor problems, as well as their respective solutions.

Steps on Fixing an Okin Recliner Motor

First, we’ll help you pinpoint the problem so that we can explain how to resolve it. You can fix it without calling a technician or spending a lot of money.

Step 2: The gearbox is likely to be the source of the noise your motor is making when you try to start it. Once you’ve disconnected the motor from the gearbox, you can remove the nuts. You’ll need to take it apart, replace both gears, and then reassemble it to fix this.

Recliner-Handles Okin BetaDrive Linear Actuator Motor - Recliner-Handles

Step 3.  It’s likely that one or more brushes are missing on the armature (the spinning part) if your motor turns on but won’t run when given an input voltage.

To resolve this issue, the armature must be taken out of the motor and inspected for damage or missing components. The alternative to purchasing new brushes (you’ll need two) is to fashion a D-shaped wire by cutting a length of wire and bending the ends together to form a single long end with a loop in the middle.

Each brush on the armature will require its own.

In case the first two steps fail, the motor’s electronic controller may have an overload switch or thermal fuse to prevent the motor from overheating and burning out.

You should check the thermal fuse and the overload switch to make sure they are not tripped. If these are fine, then you can remove the recliner’s bottom panel to access the motor and any other wires or circuit boards that may be dangling loosely.

What is Okin Recliner?

Reclining chairs are Okin’s specialty, and they’ve created a brand called the brand. As a business, they’ve been around for quite some time.

Since 1895, when they made their first wooden chair as an alternative to metal furniture that might be too heavy or uncomfortable to sit on for extended periods of time, Okin has been in business.

Okin now offers multiple variations of their popular reclining chairs. Each one is crafted to ensure a pleasant wearing experience and long life.

How to Deep Clean Okin Recliner Motor

Wear protective equipment, such as gloves and goggles, and spray the motor with a degreasing spray, such as WD-40, to remove any built-up dirt, grease, or grime.

Foam seats can be damaged by degreaser, so be careful not to use too much.

Afterwards, vacuum up any dirt or dust that the degreasing spray may have left behind. If you want to get into hard-to-reach places, this is the time to use a long-hosed attachment.

Use dry rags or paper towels to scrub off any grease that has caked on.

A soapy water spray can be used to clean the foam seat or any other hard surface, followed by a dry rag.

How does the Reclining Mechanism Work?

#1. Modern iterations of Okin chairs feature a lever that can be pushed with the user’s feet to recline the chair’s back while seated.

Reclining can be stopped by pressing the footrest in front of the chair and sitting up straight.

Okin’s lever is unique in that it can be pivoted in either direction when pushed with your feet, rather than being a fixed length. Because of this, you won’t have to stretch your arm as far to push the lever as you recline because it will remain closer to your body.

#3. The Okin lever is completely manual and does not have any moving parts or need for an external power source. Due to their compact size, they are also a practical choice for apartments and smaller homes.

#4. The Okin lever has a wider than average, one-piece, solid wood base. That way, the chair won’t move around as much while you’re sitting in it.

Amazon.com: Happybuy Ap-A88 Electric Recliner Chair Motor Replacement Kit Lift Chair DC Motor Actuator Household Okin Recliner Motor Replacement for Electric Sofa Reclining Chairs Motor : Home & Kitchen

How to Prevent Wear and Tear on Okin Recliner Motor

The lever needs to be replaced if it no longer clicks and returns to its original position. You may have a problem with the motor if you see bare metal on the base of your unit or if one section of the recliner is higher than the other.

Additionally, Okin suggests changing out your levers every six to twelve months.

The Okin lever has a wider than average, one-piece, solid wood base. This provides additional support and keeps the chair in place while you use it.

Everything You Need to Know about Electric Recliner Repair

After a long day at work, there’s nothing like relaxing in a recliner or using one to get a good night’s sleep. There are a plethora of different types of recliners on the market, but the best are unquestionably electric recliners. These chairs are not only extremely cozy, but they also feature convenient buttons that let you change the angle of recline and the amount of back support. Electric recliners have the disadvantage of frequently malfunctioning. This highlights the significance of being familiar with electric recliner problems and repair methods. Luckily, the issues they face are usually not severe, and you can usually find and fix the root cause of the problem in a short amount of time. This necessitates your familiarity with the inner workings of your recliner. In this article, we’ll discuss the most frequent problems you encounter, as well as the solutions available to you. Come on, then, and we can begin.

Common issues with electric recliners

Most electric recliners will have multiple issues throughout their lifetimes. Fortunately, they can usually be corrected quickly. Inadequate attention to these issues, no matter how seemingly inconsequential, can lead to a much larger problem down the road. Here, we’ll examine potential issues and their fixes so that your recliner is always in top shape.

Undone power plugs or wires

The electrical motor in your recliner may have become unplugged or the wires may have become loosened if you have recently relocated the chair. Recliners are prone to malfunctions that can be traced back to the power plugs, even if they are in good condition and are not loose. Your recliner will not work at all if any of the connections are broken or come loose. Both are common, but the good news is that the solution may be the least complicated of all. If the outlet is fine, the problem may lie with the other end of the wire. It needs to be fixed if it’s come undone, is partially pulled out, or is frayed.

Damage due to power surges

Power surges are fairly common, and they can severely damage sensitive electric devices like the motor in your electric recliner. A power surge may only fry the engine’s transformer, saving you the cost of replacing the motor. The recliner’s motor is a simple place to start looking. The transformation is dead and needs to be replaced if you don’t see a green light or any obvious damage. Recliner motors are notoriously expensive to replace, and obvious damage to the motor means it has stopped working and needs to be replaced. You might be better off just buying a brand new, high-quality recliner. The Irene House Power Chair Recliner is a great option to consider if you’re in the market for a new powered model because of the increased mobility it provides.

Broken internal wires

When you try to adjust the recliner’s backseat or footrest, they may become stuck. A frayed wire inside your recliner could be the cause of this problem. It was probably caught between the machine’s moving parts as you opened or closed it. Breaking a wire is almost always the cause of a recliner’s mechanism stopping suddenly and making a sparking noise. When the wiring is only partially severed, it can be repaired with electrical tape and the recliner will work again. However, those that are completely dysfunctional may require an alternative approach. Your chair will lose power if any of its wires are completely severed. If the chair’s electrical wires are properly fastened to the chair’s frame, future wire damage can be avoided.

Other electrical issues

Check the outlet it is plugged into if your recliner isn’t responding to your commands. Plug an operational appliance into the outlet to test the voltage inside. If the other outlet is working, the problem isn’t with yours. Some electrical appliances are more vulnerable to disruptions in the flow of electricity and must power down to protect their sensitive internal mechanisms, wires, and motors. The recliner might stop functioning for a while if there is a surge inconsistency. You should only plug your electric recliner into an outlet that has a built-in surge protector and overload guard. To rule out the outlet as the source of the problem, try using the recliner without plugging it in and checking for electrical problems. If the battery and cables seem fine, the issue may lie with some other part of the electrical system. All of the electrical components, the lift motor, the relay boxes, the heating elements, and the massage features are contained within. A power surge or overload could have fried any number of electrical components, so it’s important to check them all. It’s also possible that several components were damaged, making repair very expensive. It could be a sign that you need a more luxurious chair, like a power lift recliner. For those who have trouble getting around, we recommend the Mcombo Electric Power Lift Recliner Chair.

Problems with motor and control parts

Other electrical issues, such as the failure of the recliner’s motor, central battery, or remote control, can cause more extensive damage. The trouble is that any of these components could potentially disrupt the operation of others. As a result, you will need to replace multiple parts of the recliner simultaneously. It’s possible that if the recliner’s motor stops working, you’ll also need to buy a battery. The situation becomes more convoluted if your recliner has a massage function or a heating element. It may be more cost-effective to purchase a new recliner if multiple key components are damaged and require replacement.

Fixing electric recliner problems

There are a number of potential issues with electric recliner chairs, just like with electric recliner sofas. Fortunately, many of these issues are preventable, and we will examine how to fix an electric recliner in this article. If you take better care of your chair and invest in a quality surge protector, you should be able to avoid the need for electric sofa recliner repair. If you weren’t able to stop the problem from happening, don’t worry about it. You shouldn’t rule out the possibility of fixing an electric recliner on your own to save money on costly professional service.

Fixing a recliner that halts midway

The failure of a recliner to fully open or close can occur for one of two main reasons. It’s likely just a simple plug or wiring problem if your electric recliner gets stuck in an open position and won’t close. Recliners often have a tendency to pull apart at the seams, which can lead to problems with things like electrical wires. The problem could have been caused by a loose in-line plug or wire; to fix it, simply locate the offending component and tighten its connections. A recliner that stalls while being closed could be a symptom of a more serious electrical problem that could be difficult to repair. There’s a chance the opening mechanism snagged or severed some of the wires. Lifting the chair, tilting it onto its side, and opening the back will reveal the broken wire, which must be repaired. Once you’ve located the wire that’s been pinched, carefully pull it out from under the mechanism. Repairing broken wires by taping them back together is an option. To avoid this problem in the future, you can tape the wiring to the frame in a location far from the opening mechanism. Taping the frayed ends of the wires together is a good temporary fix, but the wires could become disconnected again. Or it might not even work if the wiring was too badly damaged. The only way to fix your recliner then is to replace the wires that have been damaged. To save money, you can use cables similar to those already in your home and secure the connections with electrical tape. On the other hand, if you want to get the best results, you should stick with the wires the original manufacturer did.

Using the reset button

It could be as simple as pressing the reset button if you need to get your broken recliner working again. Maybe the mechanism has been overworked as a result of your recent heavy use. Or it turned off because of an electrical overload or surge. To start, try to reset the motor by unplugging the recliner, waiting a few minutes, and then plugging it back in. If that doesn’t work, try looking for the recliner’s reset button and pressing it to see if that helps. Many remote controls conceal the reset button between the “open” and “close” buttons. A small, sharp object, like the tip of a paperclip, can be used to push the reset button into action. After pressing the reset button, unplug the recliner and wait a few minutes before plugging it back in. The reset button is typically located on the motor itself or nearby. To find it, as mentioned before, you’ll need to shine a flashlight in the area and peer closely. If you push it, the motor will reset, and you should be able to use the reclining feature again.

Using a surge protector

There is a wide range of causes and manifestations for power surges, from harmless ones caused by a flipped switch on the power grid to devastating ones caused by a lightning strike. The transformer powering your recliner may be severely damaged by even a brief spike in electrical demand. Transformers are responsible for regulating motor speed. Thus, the motor and the transformer are both at risk of being damaged by the power surge, even if the motor survives. When plugging an electrical device into an outlet, it is essential and often recommended by manufacturers to use a surge protector to prevent damage that could result in expensive repairs. You can protect the motor in your recliner from potential harm and extend its life by using a surge protector.

Buy Okin Refined-R Model: JLDQ-11 & JLDQ.11.156.333P Power Recliner Lift Chair Motor Actuator Replacement Online at Lowest Price in Ubuy Nepal. B097SYYPQK

Contacting a professional

If you have already tried the recliner’s reset button and other quick-fix methods without success, it is probably time to call in the experts. Getting in touch with the vendor or the maker is your quickest and safest bet for receiving expert assistance. A free repair or new chair could be on the way if you still have time left on your recliner’s warranty. If it isn’t, don’t worry; they have the know-how to locate the precise replacement components your chair needs to keep functioning smoothly and reliably for the foreseeable future. If you don’t feel like fixing your recliner yourself, you can always contact the manufacturer or retailer. They can recommend a reliable recliner repair service that may provide additional warranties. When the warranty on your recliner has expired, it’s time to start looking for a reputable repairman in your area.

Final thoughts

Electric recliners are more advanced than their manual counterparts, but they still use a straightforward mechanism. Once you understand what’s wrong, fixing a broken electric recliner isn’t too difficult. DIY home repairs are a great alternative to costly professional maintenance. Original replacement components can be expensive, but they are usually easily accessible and inexpensive to replace if necessary. There are times when the issue is more intricate. After performing all of the above checks and attempting all of the suggested quick fixes, if your electric recliner still isn’t functioning properly, it is probably time to call a professional for electric recliner repair.